How To Cast Off Loom Knitting?

You have finished your loom knitting project and are now ready to take it off the loom, there are a few things you need to do first. Gather your materials-you will need a crochet hook in the same size as your loom needles, and yarn snips. You will also need the tapestry needle for weaving in any loose ends.

If you used a different type of yarn for cast on or bind-off, make sure to have that with you as well. Now find the end of your work-it should be at the bottom of your project if you are holding it upright. The first stitch on the needle will be a loop, and the last stitch will be a V.

Loom Knit: Cast Off – Bind Off Method | BEGINNER | The Crochet Crowd

  • To cast off loom knitting, first remove the item from the loom
  • Cut the working yarn, leaving a long tail
  • Thread the tail onto a tapestry needle and insert it into the first stitch on the loom
  • Pull the yarn through that stitch, then through the next stitch on the loom until you reach the end of the row
  • Fasten off by weaving in ends or tying a knot

E Wrap Cast off Loom

If you’re looking to add a new stitch to your knitting repertoire, the e wrap cast off is a great option! This method is quick and easy to learn, and produces a nice, clean edge on your work. To e wrap cast off, start by knitting two stitches onto your right-hand needle.

Then, insert the left-hand needle into the first stitch on the right-hand needle (the one closest to the tip), and lift it over the second stitch and off of the needle. You’ve now cast off one stitch! Repeat this process until all stitches have been cast off.

One thing to keep in mind when using this method is that it can tend to produce a slightly tighter edge than other methods. If you find that your e wrap cast off is too tight, simply try using a larger needle for the last few stitches. This will help relax the edge and make it easier to stretch over your blocking wires or pins.

How To Cast Off Loom Knitting?


How Do I Cast off My Loom Knitting?

There are a few different ways to do this depending on the type of loom you are using and the project you are working on. For small projects like hats or socks, you can simply cut the yarn at one end of the loom and pull it through all of the stitches on the other end. This will release all of the stitches from the loom so that you can finish them off by hand.

For larger projects, like afghans or blankets, you will need to remove each row of knitting from the loom one at a time. To do this, cut the yarn at one end of the row and use a crochet hook or blunt needle to pull it through all of the stitches on that row. Repeat this process until all rows have been removed from the loom.

How Do You Cast off a Rectangular Loom?

The first thing you will need to do is remove all the warp threads from the pegs. To do this, start at one end of the loom and carefully take each thread off of its peg, letting it drop down to the bottom of the loom. Once all the warp threads are removed, gently pull on both ends of your project until it is completely loose from the loom.

Next, cut off any excess yarn that is hanging off of your project. Now you will need to weave in all of your loose ends so that they are secure and won’t come undone. You can either hand-sew them in or use a crochet hook or tapestry needle to weave them in and out of the fabric.

Once all your loose ends are woven in, your project is finished and ready to enjoy!

How Do You Tie off a Loom?

When you reach the end of your project or the end of your thread, you will need to tie off your loom. This is a simple process, but it is important to do it correctly so that your project does not come undone. To tie off your loom, start by threading your tail through the last few warp threads.

Then, take the tail under the weft threads and back up through the warp threads again. Pull tight so that the weft threads are snug against the warp threads. Finally, knot the tail around one of the warp threads and trim the excess thread.

How Do You Take Something off a Round Loom?

There are a few different ways that you can take your project off of the loom, depending on what type of stitch you used and whether or not you want to save the yarn. If you used the e-wrap stitch, the process is relatively simple.

You will need to cut the working yarn, leaving about an 8” tail. Then, use a tapestry needle to thread through each loop on the peg, starting at Peg 1 and working your way around in a clockwise direction until you reach Peg 1 again. Once all of the loops are off of the pegs, pull on both ends of the yarn tail to tighten up any loose stitches.

You can then weave in your tails or tie off your project if you’re finished. If you used the stockinette stitch or another knit stitch, taking your project off of the loom is slightly more complicated but still doable. You will first need to cut the working yarn and leave a long tail (at least 12”).

Then, start at Peg 1 and slip each loop over its corresponding peg until they are all off. Next, use a tapestry needle to thread through each loop on one side of your work (again starting at Peg 1), going from front to back. Do this for both sides of your work.

Finally, pull on both tails of yarn to close up any gaps and secure your stitches. Again, you can either weave in your tails or tie them off before cutting them.


Loom knitting is a fun and easy way to knit, but casting off can be confusing for beginners. This blog post provides clear instructions on how to cast off loom knitting, with step-by-step photos to help visual learners.

After following these directions, you’ll be able to finish your project and wear it with pride!


I’m Jane and I’m the editor of! I am a long-time craft and clothing design fan who has been writing about these interests for years.

I have spent many hours studying knitting, weaving, sewing, embroidery, and quilting as well as learning about various brands and models of sewing gear and machines. In addition to this research, my work involves publishing information related to these topics in ways that will be informative for both amateur crafters like me and more experienced sewers!