If you’re looking for an alternative to the typical embroidery hoop, there are several options available. One option is to use a frame loom. This type of loom gives you more control over the tension of your fabric, which can be helpful when working with delicate fabrics.
Another option is to use a scroll frame. This can be helpful if you’re working on a large project or if you want to be able to see your work as you progress.
Embroidering for the first time (+ DIY embroidery hoop)
If you’re looking for an alternative to the standard embroidery hoop, there are a few options available. You can try using a frame loom, which is essentially a small weaving loom that can be used for embroidery. Or, you can try an embroidery ring, which is basically a large metal ring with an inner hoop that you can use to stretch your fabric.
Whichever method you choose, just make sure that your fabric is stretched tight so that your stitches don’t end up looking messy.
Diy Embroidery Hoop
Embroidery hoops come in all shapes and sizes, but they all serve the same purpose – to hold your fabric taut while you stitch. If you’re new to embroidery, or are looking for a more budget-friendly option, then a DIY embroidery hoop might be the way to go.
To make your own embroidery hoop, you will need:
– A piece of wood (we used a 1″ x 6″ board)
– A saw (to cut the wood to size)
– A drill (to create pilot holes)
– Screws (to secure the two halves of the hoop together)
+ Rubber bands or string (to keep the fabric tight within the hoop)
The first step is to cut your piece of wood down to size.
We used a 1″ x 6″ board, but you can use whatever size you like – just keep in mind that the larger the board, the larger your finished hoop will be. Once your board is cut to size, use a drill to create two pilot holes near each end. These pilot holes will make it easier to screw the two halves of the hoop together later on.
Credit: www.youtube.com
Can You Do Embroidery Without a Hoop?
Yes, you can do embroidery without a hoop. The key is to use a stabilizer to keep your fabric from shifting. There are several types of stabilizers you can use.
For lightweight fabrics, use a tear-away or cut-away stabilizer. For heavier fabrics, use a heat-activated or water-soluble stabilizer. Be sure to test your stabilizer on a scrap piece of fabric before using it on your project.
How Do You Make an Embroidery Hoop?
You will need:
-a piece of wood (we used a 1×8 pine board cut down to 6 inches)
-a miter saw or hand saw
-a drill
-1 inch dowel rod
-Titebond II wood glue
-clamps
-sanding block & sandpaper (120, 220, 400 grit)
-wood finish of your choice ( we used Danish oil)
The first step is to cut your wood into two pieces using a miter saw or hand saw. Our 1×8 pine board was cut down to 6 inches.
You will then want to use a drill and dowel rod to create a hole at each end of both pieces of wood. The dowel rod should be slightly smaller than the width of your chosen embroidery hoop so it can fit snugly inside.
Next, apply Titebond II wood glue around the circumference of one end of each piece of wood before inserting the dowel rod into the holes.
Make sure the holes are aligned before clamping the two pieces together and letting them dry overnight. Once the glue has dried, you can use a sanding block with 120 grit sandpaper to smooth out any rough edges before moving on to 220 and then 400 grit sandpaper until the surface is nice and smooth.
To finish, apply your desired wood finish – we used Danish oil – according to the manufacturer’s instructions.
Now you have a beautiful new embroidery hoop that’s ready for all your future stitching projects!
How Do You Sew Without a Hoop?
There are a few ways that you can sew without a hoop. One way is to use a frame. You can either make your own frame or purchase one.
Another way is to use a piece of cardboard or something similar. Just make sure that whatever you use is sturdy enough to hold your fabric in place while you sew.
If you don’t have anything to use as a frame, another option is to simply hold the fabric in place with your hands.
This method works best for smaller pieces of fabric. Just be careful not to stretch the fabric too much as you sew, or it will distort the shape of your finished project.
Conclusion
There are a few things you can use instead of an embroidery hoop! You can use a frame, tape the fabric to a table, or even your own hand. Whatever you use, just make sure it’s tight so the stitches don’t pucker.
